Auto Parts Search
2007 Ford E-250 CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
BRAKE SERVICE PROCEDURES FOR 2007 Ford E-250 AUTOMOBILES
Power Brake Units -> Bendix Vacuum Brake Booster -> Diagnosis & Testing
Vehicle: 2007 Ford E-250 4.6 V8 GAS
Refer to Figs. and f...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford E-250 BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford E-250 AUTOMOBILES
DRIVESHAFT, Replace -> One Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2007 Ford E-250 4.6 V8 GAS
One Piece Driveshaft
- Raise and support vehicle.
- To maintain driveline balance, index-mark driveshaft flange yoke and pinion flange.
- Index-mark driveshaft yoke and transmission tailshaft. Do not allow output shaft to turn.
- Remove four driveshaft to pinion flange bolts.
- Disconnect driveshaft flange yoke from pinion flange, using a suitable tool as shown. Driveshaft flange yoke fits tightly on pinion flange pilot. Never hammer on driveshaft or any of its components to disconnect yoke from flange. Pry only in area shown, with a suitable tool, to disconnect yoke from flange.
- Lower driv...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford E-250 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2007 Ford E-250 AUTOMOBILES
Starter, Replace
Vehicle: 2007 Ford E-250 5.4 V8 GAS
- Disconnect battery ground cable.
- Raise and support vehicle.
- Remove starter motor solenoid terminal cover.A protective cap or boot is provided over battery input terminal on all vehicle lines and must be reinstalled after repair. Failure to follow this instruction may result in damage to vehicle.
- Remove starter solenoid S-terminal nut and S-terminal eyelet.
- Remove starter solenoid B-terminal nut and B-terminal eyelet.
- Remove starter...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford E-250 STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2007 Ford E-250 AUTOMOBILES
Ford Motor Co. Trucks -> Check Engine Lamp -> 2007-09 EEC-V -> Keep Alive Memory (KAM) Reset & PCM Reset Less Electronic Tester -> PCM Reset Using Generic Scan Tool
Vehicle: 2007 Ford E-250 4.6 V8 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected by the EEC-V system. If the lamp remains On or starts to blink, a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
The lamp illuminates when the ignition is first turned to the on position to check the ...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford E-250 MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2007 Ford E-250 AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2007 Ford E-250 5.4 V8 GAS
Lower
- Drain cooling system into a suitable container.
- Reposition hose clamp from radiator.
- Remove radiator outlet hose from radiator.
- Remove hose from oil filter adapter hose and heater tube assembly.
- Reposition hose clamp from oil filter adapter.
- Remove radiator outlet hose from oil filter adapter...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford E-250 RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2007 Ford E-250 AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2007 Ford E-250 5.4 V8 GAS
- Rotate drive belt tensioner counterclockwise, using a 1/2 square hole in drive belt tensioner pull...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford E-250 SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2007 Ford E-250 AUTOMOBILES
Component location diagrams for most 2007 Ford E-250 cars and light trucks sold in the U.S. from 1990+.
Engine Diagram for 2007 Ford E-250 4.6 V8 GAS Components on diagram: |
Transmission Diagram for 2007 Ford E-250 5.4 V8 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2007 Ford E-250 PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2007 Ford E-250 AUTOMOBILES
OEM drawn wiring diagrams for most 2007 Ford E-250 cars and light trucks sold in the U.S.
2007 Ford E-250 5.4 V8 GAS Wiring Diagram Components on diagram: |
2007 Ford E-250 5.4 V8 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2007 Ford E-250 WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2007 Ford E-250 AUTOMOBILES
OEM TSB listings for most 2007 Ford E-250 cars and light trucks sold in the U.S. from 1985+.
Document: MALFUNCTION INDICATOR LAMP (MIL) ON WITH DTC P0456 - REVISED Vehicle: 2007 Ford E-250 4.6 V8 GAS Auto Systems: |
Document: RECALL - FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAIL Vehicle: 2007 Ford E-250 4.6 V8 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2007 Ford E-250 TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2007 Ford E-250 AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2007 Ford E-250 cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2007 Ford E-250 cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2007 Ford E-250 cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2007 Ford E-250 cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2007 Ford E-250 SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2007 Ford E-250 vehicle. |
Access the Complete guide! |