Auto Parts Search
2009 Chrysler Sebring CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Chrysler REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Technical Service Bulletins
- Specifications
- Brake Service
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2009 Chrysler Sebring car and truck
repair procedures including Chrysler engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Chrysler Sebring automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2009 Chrysler Sebring AUTOMOBILES
Drum Brakes -> Caliber, Avenger & Sebring Sedan -> Inspection -> Adjuster Mechanism -> Backing Plate -> Brake Drums -> Brake Linings & Springs -> Parking Brake Cable
Vehicle: 2009 Chrysler Sebring Touring 2.4 L4 GAS
Brake Drums
When brake drums are removed for brake service, the braking surface diameter should be inspected with a suitable brake drum micrometer at several points to determine if they are within the safe oversize limit stamped on the brake drum outer surface. If the braking surface diameter exceeds specifications, the drum must be replaced. If the braking surface diameter is within specifications, drums should be cleaned and inspected for cracks, scores, deep grooves, taper, out of round and heat spotting. If drums are cracked or heat spotted, they must be replaced. Scoring and groo...
CLICK HERE TO GET FULL ACCESS TO 2009 Chrysler Sebring BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Chrysler Sebring AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2009 Chrysler Sebring Touring 2.4 L4 GAS
- On models equipped with anti-lock brakes, disconnect front speed sensor.
- On all models, remove brake hose clip and cotter pin.
- Remove drive shaft nut, Fig. .
- Loosen but do not remove ball joint nut using steering linkage puller tool No. MB991113, or equivalent.
- Loosen but do not remove tie rod end using steering linkage puller tool No. MB991113...
CLICK HERE TO GET FULL ACCESS TO 2009 Chrysler Sebring DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 Chrysler Sebring AUTOMOBILES
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Trouble Code Identification -> Intermittent & Poor Connections -> Intermittents -> Low Pressure -> Poor Connections -> System Fault -> TPMS Check
Vehicle: 2009 Chrysler Sebring Touring 2.7 V6 FLEX
Accessing Diagnostic Trouble Codes
Connect a suitably programmed scan tool to DLC (Data Link Connector) and follow manufacturer's instructions.
Diagnostic Trouble Code Identification
Refer to Fig. for diagnostic trouble code identification.
Clearing Diagnostic Trouble Codes
Connect a suitably programmed scan tool to DLC (Data Link Connector), and follow manufacturer's instructions.
TPMS Check
When diagnosing a TPMS problem, first check the TPMS indicator lamp with ignition switch in the On position. From the Off position, turn the ignition key to On and check the TPMS indicator la...
CLICK HERE TO GET FULL ACCESS TO 2009 Chrysler Sebring TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2009 Chrysler Sebring AUTOMOBILES
Alternator, Replace
Vehicle: 2009 Chrysler Sebring LX 2.7 V6 FLEX
- Disconnect and isolate battery ground cable at battery.
- Remove radiator fan.
- Remove alternator drive belt.
- Remove lower mounting bolt.
- Unsnap plastic protective cover from B+ mounting stud.
- Remove B+ terminal mounting nut and B+ terminal at rear of alternator.
- Disconnect field wire electrical ...
CLICK HERE TO GET FULL ACCESS TO 2009 Chrysler Sebring STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2009 Chrysler Sebring AUTOMOBILES
Cabin Air Filter Service -> Chrysler LLC -> 2007-09 Avenger & Sebring
Vehicle: 2009 Chrysler Sebring Touring 2.4 L4 GAS
The cabin air filter should be replaced every 12,000 miles.
- Open the glove compartment.
- Push inward on the sides of the glove compartment bin, then lower the glove compartment.
- Remove the clip securing the dampener from the bin clip hole by sliding the retaining clip rearward.
- Pivot the glove compartment downward and detach the hooks from the instrument panel.
- Remove the glove compartment.
- Release the two tabs retaining the cabin air filter cover to the A/C-heater housing, then remove the cover, Fig. .
- Remove the cabin air filter element from the A/C-heater housing, Fig. .
- Ins...
CLICK HERE TO GET FULL ACCESS TO 2009 Chrysler Sebring CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Chrysler Sebring AUTOMOBILES
Chrysler LLC Cars -> Power Loss/Limit Lamp -> Chrysler, Dodge & Plymouth
Vehicle: 2009 Chrysler Sebring LX 2.4 L4 GAS
The Power Loss/Limit lamp should light for approximately 3 seconds after the ignition has been turned On as a bulb inspection. If improper or no signals are received by the logic module from various sensors, the logic modul...
CLICK HERE TO GET FULL ACCESS TO 2009 Chrysler Sebring MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2009 Chrysler Sebring AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 2009 Chrysler Sebring LX 2.4 L4 GAS
Inlet
- Drain coolant into a suitable container.
- Loosen hose clamp connecting hose to heater core inlet tube.
- Loosen hose clamp connecting hose to heater return tube.
- Remove hose from vehicle.
- Reverse procedure to ...
CLICK HERE TO GET FULL ACCESS TO 2009 Chrysler Sebring RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2009 Chrysler Sebring AUTOMOBILES
Serpentine Drive Belt, Replace -> Air Conditioning Compressor & Alternator Belt -> Installation -> Removal
Vehicle: 2009 Chrysler Sebring Touring 2.7 V6 GAS
Air Conditioning Compressor & Alternator Belt
Removal
- Raise and support vehicle.
- Remove righthand front tire and wheel assembly.
- Remove drive belt splash shield.
- Insert suitable 3/8 inch drive breaker bar into square opening of belt tensioner pivot plate.
- Rotate belt tensioner clockwise until tensioner bottoms out, then r...
CLICK HERE TO GET FULL ACCESS TO 2009 Chrysler Sebring SERPENTINE BELT SERVICE PROCEDURES
TECHNICAL SERVICE BULLETINS FOR 2009 Chrysler Sebring AUTOMOBILES
OEM TSB listings for most 2009 Chrysler Sebring cars and light trucks sold in the U.S. from 1985+.
|
Document: Pre Delivery - Front Brake Rotor Corrosion Inspection & Procedure Vehicle: 2009 Chrysler Sebring LX 2.7 V6 GAS Auto Systems: |
|
Document: Hard To Fill Or Fuel Nozzle Shuts Off Repeatedly Vehicle: 2009 Chrysler Sebring LX 2.7 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2009 Chrysler Sebring TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2009 Chrysler Sebring AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2009 Chrysler Sebring cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2009 Chrysler Sebring cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2009 Chrysler Sebring cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2009 Chrysler Sebring cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2009 Chrysler Sebring SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2009 Chrysler Sebring vehicle.
|
| Access the Complete guide! |
