Auto Parts Search
Ford Crown Victoria CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Year
| 2009 | 2008 | 2007 | 2006 |
| 2005 | 2004 | 2003 | 2002 |
| 2001 | 2000 | 1999 | 1998 |
| 1997 | 1996 | 1995 | 1994 |
| 1993 | 1992 |
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about Ford Crown Victoria car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Ford Crown Victoria automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR Ford Crown Victoria AUTOMOBILES
Air Conditioner and Heater Service Includes module configuration procedures, general service, maintenance, automatic temperature control, compressor services, electric cooling fans, vacuum diagrams, specifications, and manual air conditioning and heater diagnostics and replacement procedures for domestic and imported Ford Crown Victoria cars and light trucks from 1990+
General Service Domestic Vehicles -> 1992-93 -> Exercise System
Vehicle: 1992 Ford Crown Victoria 4.6 V8 GAS
An important fact most car owners ignore is that the A/C system must be used periodically. Car manufacturers caution that when the air conditioner is not used regularly, particularly during cold months, it should be turned on for a few minutes once every two or three weeks while the engine is running. This keeps the system in good operating condition.
Checking out the system for the effects of disuse before the onset of summer is one of the most important asp...
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR Ford Crown Victoria AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported Ford Crown Victoria cars and light trucks from 1990+.
Power Brake Units -> Adjustments -> Bendix Type -> Escort, Tracer & ZX2 -> Except Escort, Tracer & ZX2 -> Pushrod -> Single Diaphragm Booster
Vehicle: 1998 Ford Crown Victoria Police Interceptor 4.6 V8 CNG
On Vehicles Equipped With Anti-Lock Brakes Refer To "Anti-Lock Brakes".
Pushrod
Proper adjustment of the master cylinder pushrod is necessary to ensure proper operation of the power brake system. A pushrod that is too long will prevent the master cylinder piston from completely releasing hydraulic pressure, eventually causing the brakes to drag. A pushrod that is too short will cause excessive brake pedal travel and cause groaning noises to come from the booster when the brakes are applied. A properly adjusted pushrod that remains assembled to the booster with which is was matched durin...
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR Ford Crown Victoria AUTOMOBILES
Fuel filter replacement procedures with corresponding images for most domestic and imported Ford Crown Victoria cars and light trucks sold in the U.S. for 1980+.
Ford Motor Co. Passenger Cars -> Component Locations -> 2003-04 Marauder, 1987-06 Crown Victoria, Grand Marquis & Town Car
Vehicle: 1998 Ford Crown Victoria S 4.6 V8 CNG
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR Ford Crown Victoria AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported Ford Crown Victoria cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 1998 Ford Crown Victoria Police Interceptor 4.6 V8 GAS
- Raise and support vehicle.
- Index-mark driveshaft. Place a paint index-mark on pinion flange to driveshaft centering socket yoke.
- Remove driveshaft-to-driveshaft pinion flange bolts.
- Place a paint index-mark on driveshaft slip-yoke to transmissio...
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR Ford Crown Victoria AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported Ford Crown Victoria cars and light trucks sold in the U.S. from mid 1990's+.
Component Locations
Vehicle: 2008 Ford Crown Victoria 4.6 V8 FLEX
Refer to F...
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR Ford Crown Victoria AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported Ford Crown Victoria cars and light trucks from 1990+.
Starter, Replace
Vehicle: 1996 Ford Crown Victoria S 4.6 V8 GAS
- Disconnect battery ground cable.
- Raise and support vehicle.
- Remove starter shield, if required.
- Disconnect starter cable and push on connector. When disconnecting hardshell connector at S-terminal, grasp plastic shell and pull off. Do not pull on wire. Be careful to pull straight off to prevent damage to connector and S-terminal. If any part of connect...
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR Ford Crown Victoria AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported Ford Crown Victoria cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Check Engine Lamp/Malfunction Indicator Lamp (MIL)/Service Engine Soon Lamp -> 1995-97 Models -> EEC-IV -> EEC-V -> Keep Alive Memory (KAM) Reset & PCM Reset Less Electronic Tester -> PCM Reset Using Generic Scan Tool -> PCM Reset Using Star Tester
Vehicle: 1997 Ford Crown Victoria LX 4.6 V8 CNG
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected by the EEC-IV system. A diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
EEC-IV
PCM Reset Using Star Tester
- Turn ignition Off.
- Perform required vehicle preparation and visual inspection.
- Connect Star teste...
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR Ford Crown Victoria AUTOMOBILES
Includes radiator, cooling and heater hose replacement procedures for domestic and imported Ford Crown Victoria cars and light trucks from 1990+
Radiator, Replace
Vehicle: 1996 Ford Crown Victoria LX 4.6 V8 GAS
- Turn lower fan shroud in upper fan shroud to allow clearance for fan shroud removal.
- Disconnect cooling fan electrical connector at righthand side of fan shroud.
- Remove radiator upper sight shield.
- Loosen fan shroud from its radiator mounting, then remove lower radiator hose from supports on fan shroud.
- Lift fan shroud and electric cooling fan assembly out of vehicle.
- Disconnect transmission oil co...
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR Ford Crown Victoria AUTOMOBILES
Serpentine belt replacement procedures with corresponding images for most domestic and imported Ford Crown Victoria cars and light trucks sold in the U.S. from 1990+.
Serpentine Drive Belt, Replace
Vehicle: 2008 Ford Crown Victoria LX 4.6 V8 GAS
- Rotate tensioner away from belt using a breaker bar installed in 1/2 inch square hole in tensioner arm.
- Lift old belt over alternator pulley...
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR Ford Crown Victoria AUTOMOBILES
Component location diagrams for most Ford Crown Victoria cars and light trucks sold in the U.S. from 1990+.
 Engine Compartment Component Locations Diagram for 1994 Ford Crown Victoria LX 4.6 V8 GASComponents on diagram: |
 Engine Diagram for 2008 Ford Crown Victoria LX 4.6 V8 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR Ford Crown Victoria AUTOMOBILES
OEM drawn wiring diagrams for most Ford Crown Victoria cars and light trucks sold in the U.S.
 2007 Ford Crown Victoria Police Interceptor 4.6 V8 GAS Wiring DiagramComponents on diagram: |
 1997 Ford Crown Victoria S 4.6 V8 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR Ford Crown Victoria AUTOMOBILES
OEM TSB listings for most Ford Crown Victoria cars and light trucks sold in the U.S. from 1985+.
|
Document: IC - MODIFY TO PROVIDE ABS INDICATOR CIRCUITS-RECALL Vehicle: 1992 Ford Crown Victoria Touring Sedan 4.6 V8 GAS Auto Systems: |
|
Document: TRANSMISSION FLUID USAGE CHARTS Vehicle: 1996 Ford Crown Victoria Police Interceptor 4.6 V8 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR Ford Crown Victoria AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most Ford Crown Victoria cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most Ford Crown Victoria cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most Ford Crown Victoria cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most Ford Crown Victoria cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO Ford Crown Victoria SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your Ford Crown Victoria vehicle.
|
| Access the Complete guide! |
