Auto Parts Search
Toyota CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Toyota REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Model
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about Toyota car and truck repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up & drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix your Toyota automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR Toyota AUTOMOBILES
Air Conditioner and Heater Service Includes module configuration procedures, general service, maintenance, automatic temperature control, compressor services, electric cooling fans, vacuum diagrams, specifications, and manual air conditioning and heater diagnostics and replacement procedures for domestic and imported Toyota cars and light trucks from 1990+
Toyota -> Component Replacement & Adjustment -> Instrument Panel, Replace -> 1996 -> 1997 -> 4Runner -> Avalon -> Camry -> Celica -> Corolla -> Land Cruiser -> Paseo -> RAV4 -> T100 -> Tacoma -> Tercel
Vehicle: 1996 Toyota Previa LE 2.4 L4 GAS
Avalon
- Remove front pillar garnish.
- Remove front door inside scuff plate.
- Remove hood lock release lever.
- Remove cowl side trim.
- Remove steering wheel and steering column cover, Fig. .
- Remove combination switch.
- Remove lower finish panel.
- Remove instrument panel finish lower lefthand panel.
- Remove fuse box bolt.
- Remove No. 2 duct heater to register.
- Remove parking brake release lever.
- Remove No. 2 undercover.
- Remove lower No. 2 finish panel.
- Remove glove compartment door and glove compartmen...
CLICK HERE TO GET FULL ACCESS TO Toyota A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR Toyota AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported Toyota cars and light trucks from 1990+.
DISC BRAKES -> Front Disc Brakes -> DISC BRAKE SPECIFICATIONS
Vehicle: 1994 Toyota Pickup SR5 3.0 V6 GAS
Refer to the disc brake specifications under "Rear ... "
CLICK HERE TO GET FULL ACCESS TO Toyota BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR Toyota AUTOMOBILES
Fuel filter replacement procedures with corresponding images for most domestic and imported Toyota cars and light trucks sold in the U.S. for 1980+.
Toyota -> Fuel Filter Scheduled Maintenance -> 1986-06 Models -> Normal Service -> Severe Service
Vehicle: 2005 Toyota Corolla 1.8 L4 GAS
Normal Service
Service as r...
CLICK HERE TO GET FULL ACCESS TO Toyota FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR Toyota AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported Toyota cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2009 Toyota Tundra 4.7 V8 GAS
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- On models equipped with 4WD, drain differential oil into suitable container.
- On all models, remove hub cap and cotter pin.
- Apply brakes and remove lefthand driveline hub nut.
- Remove bolt and nuts and separate lefthand front suspension arm subassembly from lower ball joint.
- Disengage driveshaft from axle hub using plastic hammer.
- Push steering knuckle outward and disconnect driveshaft from stee...
CLICK HERE TO GET FULL ACCESS TO Toyota DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR Toyota AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported Toyota cars and light trucks sold in the U.S. from mid 1990's+.
Wiring Diagrams -> Wire Color Code Identification
Vehicle: 2008 Toyota Yaris S 1.5 L4 GAS
Refer to Fig. for wiring...
[[table data]]CLICK HERE TO GET FULL ACCESS TO Toyota TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR Toyota AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported Toyota cars and light trucks from 1990+.
Alternator, Replace
Vehicle: 1992 Toyota MR2 2.0 L4 GAS
- Disconnect battery ground cable from negative terminal of battery. Turn ignition switch to LOCK. Wait at least 20 seconds before proceeding with work.
- Loosen pivot bolt and adjusting lock bolt.
- Loosen adjustin...
CLICK HERE TO GET FULL ACCESS TO Toyota STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR Toyota AUTOMOBILES
Cabin air filter locations and replacement procedures with corresponding images for most domestic and imported Toyota cars and light trucks sold in the U.S. as equipped to the current model year.
Cabin Air Filter Service -> Toyota -> 2002-06 Camry, 2002-08 Camry Solara & 2005-06 Sienna
Vehicle: 2005 Toyota Camry 2.4 L4 GAS
On 2002-03 models, under normal operating conditions the cabin air filter should be replaced every 15,000 miles. In dusty areas change the cabin air filter every 10,000 miles.
On 2004-08 models, the cabin air filter should be cleaned every 18 months or 15,000 miles and replaced every 36 months or 30,000 miles. The filter should be replaced more often if air flow is less than normal.
- Open the glove compartment door.
- Remove the screw retaining the damper rod to the righthand side of the glove compartment door, then detach the damper rod.
- Push inwar...
CLICK HERE TO GET FULL ACCESS TO Toyota CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR Toyota AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported Toyota cars and light trucks sold in the U.S. from 1990+.
Toyota -> Malfunction Indicator Lamp (MIL) ->
Vehicle: 2007 Toyota Highlander 2.4 L4 GAS
On some models equipped with OBD II, the MIL will also illuminate if the fuel tank filler cap is not properly tightened. Tighten fuel tank filler cap until it clicks.
The MIL should light when the ignition switch is placed in the On position without starting the engine. When the engine is started, the lamp should go out. If it remains lit, a fault has been detected by the diagnostic system and has logged a diagnostic trouble code. If the fault does not occur again within three trips, the lamp will go out but a diagnostic tro...
CLICK HERE TO GET FULL ACCESS TO Toyota MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR Toyota AUTOMOBILES
Includes radiator, cooling and heater hose replacement procedures for domestic and imported Toyota cars and light trucks from 1990+
Radiator, Replace
Vehicle: 2010 Toyota RAV4 Sport 2.5 L4 GAS
- Disconnect battery ground cable.
- Remove six screws and A/C air intake duct.
- Remove engine under cover.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- On models with automatic transaxle, disconnect A/T cooler hoses. Some oil will leak, catch it in a suitable container. Plug pipe to prevent oil from escaping.
- On all models, disconnect ra...
CLICK HERE TO GET FULL ACCESS TO Toyota RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR Toyota AUTOMOBILES
Serpentine belt replacement procedures with corresponding images for most domestic and imported Toyota cars and light trucks sold in the U.S. from 1990+.
Serpentine Drive Belt, Replace
Vehicle: 2007 Toyota Sequoia SR5 4.7 V8 GAS
- Remove V-Bank cover subassembly.
- Remove bolts from engine under cover assembly, then remove cover.
- Rotate or lift belt tensioner arm counterclockwise, using a suitable tool to...
CLICK HERE TO GET FULL ACCESS TO Toyota SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR Toyota AUTOMOBILES
Component location diagrams for most Toyota cars and light trucks sold in the U.S. from 1990+.
Emission Control Component Locations Diagram for 1990 Toyota Celica ALL Trac 2.0 L4 GAS Components on diagram: |
Body Components Diagram for 2007 Toyota Avalon XL 3.5 V6 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO Toyota PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR Toyota AUTOMOBILES
OEM drawn wiring diagrams for most Toyota cars and light trucks sold in the U.S.
2006 Toyota Highlander Hybrid 3.3 V6 ELECTRIC/GAS Wiring Diagram Components on diagram: |
2005 Toyota Highlander 3.3 V6 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO Toyota WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR Toyota AUTOMOBILES
OEM TSB listings for most Toyota cars and light trucks sold in the U.S. from 1985+.
Document: TRIM GARNISH LOOSE Vehicle: 2003 Toyota Solara 2.4 L4 GAS Auto Systems: |
Document: BATTERY MAINTENANCE FOR IN-STOCK VEHICLES Vehicle: 1996 Toyota Avalon XL 3.0 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO Toyota TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR Toyota AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most Toyota cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most Toyota cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most Toyota cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most Toyota cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO Toyota SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your Toyota vehicle. |
Access the Complete guide! |